1、保護車底金屬與水隔離，避免生鏽

2、堵塞部件聯接縫隙，緊扣螺丝避免行駛中脫落；

3、隔除車底噪音傳播，防止砂石撞擊損害；

4、提高車內行駛舒适感，延长車輛使用壽命

品牌：UD優道

系統：全車防鏽

底盤裝甲

産品編号：UD-023 1000ML

企業标準：Q/YK 044-2011

僅供4S店使用

産品性能:

1、保護車底金屬與水隔離，避免生鏽

2、堵塞部件聯接縫隙，緊扣螺丝避免行駛中脫落；

3、隔除車底噪音傳播，防止砂石撞擊損害；

4、提高車內行駛舒适感，延长車輛使用壽命

使用方法：

1.将車底需噴塗的(de)部件徹底清潔，如有鏽迹應鏟除、砂光，达到無塵，無水，無油，無蜡迹将不需噴塗的(de)部位（排气管、發動機、水箱、彈簧、空調冷凝器等）進行嚴密覆蓋。

2.充分搖動本品約2分鐘，打開灌蓋，去除封口，插入本廠專用噴槍，連接0.6-0.8Mpa壓縮空气。在距離噴塗表面約25cm處，来回均勻噴塗。

3.为防止流痕和松垂，建議分三次噴塗。在第一次噴塗完成後，对孔洞，裂縫處使用車膩子填封、刮平；待前一次噴塗干燥後（不少于15分鐘）再進行噴塗。厚度达到1.5mm以上隔音效果明顯。

4.本品未干固前可用汽油清洗

注意事項：

眼睛接觸,請立即用大量的(de)清水清洗,並立即就醫;

如果誤食,不要催吐,立即就醫,並出示該物品的(de)盛裝容器或标签。

Armored chassis (oily)

properties:

1, protect the car with water metal isolation, avoid rust

2 and plugging parts connected to the aperture, gripping screw avoid driving fall off;

3, the car in addition to the noise propagation, prevent sand crash damage;

4, improve in-car driving comfort, prolong the service life of the vehicle

Usage :

1. To spray parts of the car will thoroughly clean, if have should be razed and rust sanding, to clean, no water, no oil, no wax mark will need not spraying parts (the exhaust, engine, water tank, spring, air conditioner condenser, etc) closely covered. 

2. Fully moved this article about 2 minutes, open the irrigation cover, remove the seal and insert the factory special spray gun, connection-0.6 Mpa compressed air. In the distance spraying the surface of about 25 cm place, spray evenly back and forth.

3. To prevent flow mark and baggy, suggested in three spraying. In the first time after the completion of the spraying of hole, crack in car use, to blow be bored with child fill seal flat; For a time after dry before spraying (not less than 15 minutes) and then spraying. 1.5 mm thickness above sound insulation effect is obvious.

4. This product did not work to solid available before gasoline to clean

Note:

Avoiding Any Eye Contact ,if contact, please immediately with plenty of clean flowing water and seek medical advice immediately;

If swallowed, don't spits, seek medical advice immediately and show this container or label the dress items.