品牌：爱蔻

系統：燃油系統

缸內積碳清除劑

産品編号：

企業标準：Q/YKJH 4

僅供4S店使用

 産品性能： 

1、有效清洗燃燒室、活塞、活塞环槽、等部件上的(de)積炭、附着物；

2、快速釋放卡死在活塞环槽中的(de)活塞环,恢複活塞环的(de)彈性及運動性；

3、 降低機油的(de)消耗量；降低發動機的(de)工作噪音； 降低有害气體的(de)排放；

4、 均衡气缸壓力，提升動力、节省燃油。

使用方法：

1、預热發動機並使其處在温热（而不是炙热）狀态；

2、拆下火花塞（或者噴油嘴），切斷点火分電器、高壓点火圈或者電瓶之間的(de)導線連接；

3、把缸內積碳清除劑直接倒進燃燒室內（分别对其他气缸重複以上動作）、重新擰上火花塞，静置10-20分鐘後，再卸下火花塞，用吸收性好的(de)布将气缸口遮蓋，以使噴出的(de)髒物不至于落到漆面上，用啟動馬达啟動發動機幾秒鐘；

4、分别用破布塞緊各气缸的(de)火花塞孔，啟動發動馬达讓破布沖出来，裝上火花塞或者（噴油嘴）；

5、啟動發動機，以高怠速運行15分鐘，以便使剩餘的(de)已經软化的(de)積碳能通过排气管排出。

備注：

1、請避免将本産品掉在汽車漆面上；

2、本産品对三元催化器、氧傳感器、橡胶制品及密封件無不良影響；

3、使用該産品後無需更換潤滑油。

Product performance:

1. Effectively clean carbon deposits and attachments on combustion chamber, piston, piston ring groove and other parts;

2. Quickly release the piston ring stuck in the piston ring groove and restore its elasticity and mobility;

3. Reduce oil consumption; Reduce the working noise of the engine; Reducing the emission of harmful gases;

4. Balance cylinder pressure, improve power and save fuel.

Usage:

1. Preheat the engine and keep it warm (not hot);

2. Remove the spark plug (or nozzle) and cut off the wire connection between the ignition distributor, high voltage ignition coil or battery;

3, pour the carbon removal agent in cylinder directly into the combustion chamber (repeat the action of other cylinder respectively), the screw on the spark plug, let stand for 10 to 20 minutes, then remove the spark plug, the cylinder mouth with good absorbent cloth cover, to make out the dirt not fall on the paint surface, start the motor start the engine for a few seconds;

4. Tighten the spark plug holes of each cylinder with the rag stopper respectively, start the motor to let the rag rush out and install the spark plug or (fuel injection nozzle);

5. Start the engine and run at a high idle speed for 15 minutes so that the remaining softened carbon deposits can be discharged through the exhaust pipe.

Remark:

1. Please avoid dropping this product on the automobile paint;

2. This product has no adverse effect on ternary catalytic converters, oxygen sensors, rubber products and sealing parts;

3. There is no need to replace lubricating oil after using this product.